安装济南卷帘门是先将框装到洞口内，然后安装扇和玻璃等。在对门窗进行安装前应先将不同规格的门窗框搬到相应的洞口旁竖放。如发现保护腹脱落，应补贴保护膜，因为保护膜是卷帘门的后一遭保护，没有保护膜的门窗是很难保护好的。

　　Installation of Ji'nan shutter door is the first box into the hole, and then install fans and glass. In the installation of doors and windows, should be different specifications of the doors and windows moved to the next entrance of the corresponding vertical. If it is found that the protection of abdominal abscission, should be subsidized protective film, because the protective film is the last screen door was protected, there is no protective film doors and windows are difficult to protect.

　　在安装将窗框放入洞口，使其上下框中线应与洞口上的安装中线对齐，并在框的四周及中蜒处用水模或垫块塞紧作临时固定，然后按设计困纸要求确定窗框在洞口罐体厚度方向的安装位置，以及安装高度，并慢慢地进行调整。调整的方法就是高度人或拉出垫在框与精体之间的木模，使窗框抬高或降低，以达到所需的位置。在将窗框调整到位后，先固定两点，应选窗框的两对角点行固定，然后再次对窗框的垂直度、水平度及直角度进行调整，使其偏差小于规定的要求后，再将其他螺钉分别固定牢固即可。

　　In the installation of the window frame into the hole, the upper and lower frame line alignment with hole on the line should be installed in the box, and the water in and around the winding mould or pad plugged for temporary fixing, and then according to the design requirements to determine the installation position of the window frame of paper stuck in the thickness direction of the tank, and installation height, and slowly adjust. The adjustment method is highly or pull the pad between the frame and the fine wood, to raise or lower the window frame, in order to achieve the desired position. In the window frame after the adjustment in place, the first fixed points, two points shall be the first diagonal frame fixed to the window frame, then again the verticality and horizontality and angle adjustment, the deviation is less than the specified requirements, and then other screws were fixed firmly.

　　门的安装与窗的安装各有不同，门的安装应在地面装饰工程施工前进行。应根据设计图纸及门扇的开启方向，确定门框的安装位置，并把门装入洞口，安装时应采取防止门框变形的措施，无下框平开门应使竖框的下边低于地面标高线，其高度差应不小子30mm。也即竖框应至少理入地停以下30mm。而带下框的平开门或维拉门应使下框低于地商标高线，其高度差宜为10mm，也即横下框应至少埋入地坪以下10mm。然后，将上框的一个国定片固定在精体上，并用木模临时定位，同时调整门框的水平度、垂直度和直角度，当所有尺寸都到位后，就将所有的固定螺钉全部固定到位。当安装连窗门时，门与窗应采用拼撞料拼簇，饼橙料下峭应固定在窗台上。

　　The installation of doors and windows are different from each other, and the installation of doors shall be carried out before the ground decoration works. According to the design drawings and the door opening direction, determine the installation position the door frame and the door into the mouth of the cave, the installation should be taken to prevent the deformation of the frame under the door frame without measures, should make the mullion below the ground below the standard high, the height difference should be no boy 30mm. That should at least stop mullion into the following 30mm. The flat door or sliding door of the lower frame should make the lower frame mark lower than the ground mark. The height difference should be 10mm, that is to say, the lower frame should be buried below the floor at least 10mm. Then, a national film box fixed on the fine body, and wood door and temporary location, adjust the levelness and verticality and angle, when all dimensions are in place, it will be all the screws fixed in place. When installing a window, the door and window shall be made of a collision joint, and the material under the orange shall be fixed on the window sill.